
  WTware v.5.1.64

|WTware v.5.1.64 supervisor.
WTC listener is active.
WTC broadcast listener is active.
HTTPd listener is active.
[KERNEL] [ 0.000000] Linux version 3.13.11 (root@c8) (gcc version 4.8.2
(Ubuntu 4.8.2-19ubuntu1) ) #1 PREEMPT Wed May 21 18:16:09 MSK 2014
[KERNEL] [ 0.000000] KERNEL supported cpus:
[KERNEL] [ 0.000000] Intel GenuineIntel
[KERNEL] [ 0.000000] AMD AuthenticAMD
[KERNEL] [ 0.000000] NSC Geode by NSC
[KERNEL] [ 0.000000] Cyrix CyrixInstead
[KERNEL] [ 0.000000] Centaur CentaurHauls
[KERNEL] [ 0.000000] e820: BIOS-provided physical RAM map:
[KERNEL] [ 0.000000] BIOS-e820: [mem
0x0000000000000000-0x000000000009fbff] usable
[KERNEL] [ 0.000000] BIOS-e820: [mem
0x000000000009fc00-0x000000000009ffff] reserved
[KERNEL] [ 0.000000] BIOS-e820: [mem
0x00000000000f0000-0x00000000000fffff] reserved
[KERNEL] [ 0.000000] BIOS-e820: [mem
0x0000000000100000-0x000000000ffebfff] usable
[KERNEL] [ 0.000000] BIOS-e820: [mem
0x000000000ffec000-0x000000000ffeefff] ACPI data
[KERNEL] [ 0.000000] BIOS-e820: [mem
0x000000000ffef000-0x000000000fffefff] reserved
[KERNEL] [ 0.000000] BIOS-e820: [mem
0x000000000ffff000-0x000000000fffffff] ACPI NVS
[KERNEL] [ 0.000000] BIOS-e820: [mem
0x00000000ffff0000-0x00000000ffffffff] reserved
[KERNEL] [ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[KERNEL] [ 0.000000] SMBIOS 2.3 present.
[KERNEL] [ 0.000000] DMI: System Manufacturer System Name/CUV4X-M, BIOS
ASUS CUV4X-M ACPI BIOS Revision 1005.B 09/13/2000
[KERNEL] [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==>
reserved
[KERNEL] [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[KERNEL] [ 0.000000] e820: last_pfn = 0xffec max_arch_pfn = 0x100000
[KERNEL] [ 0.000000] MTRR default type: uncachable
[KERNEL] [ 0.000000] MTRR fixed ranges enabled:
[KERNEL] [ 0.000000] 00000-9FFFF write-back
[KERNEL] [ 0.000000] A0000-BFFFF uncachable
[KERNEL] [ 0.000000] C0000-C7FFF write-protect
[KERNEL] [ 0.000000] C8000-EFFFF uncachable
[KERNEL] [ 0.000000] F0000-FFFFF write-protect
[KERNEL] [ 0.000000] MTRR variable ranges enabled:
[KERNEL] [ 0.000000] 0 base 000000000 mask FF0000000 write-back
[KERNEL] [ 0.000000] 1 base 0E4000000 mask FFC000000 write-combining
[KERNEL] [ 0.000000] 2 disabled
[KERNEL] [ 0.000000] 3 disabled
[KERNEL] [ 0.000000] 4 disabled
[KERNEL] [ 0.000000] 5 disabled
[KERNEL] [ 0.000000] 6 disabled
[KERNEL] [ 0.000000] 7 disabled
[KERNEL] [ 0.000000] initial memory mapped: [mem 0x00000000-0x007fffff]
[KERNEL] [ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[KERNEL] [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[KERNEL] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[KERNEL] [ 0.000000] init_memory_mapping: [mem 0x0f400000-0x0f7fffff]
[KERNEL] [ 0.000000] [mem 0x0f400000-0x0f7fffff] page 2M
[KERNEL] [ 0.000000] init_memory_mapping: [mem 0x08000000-0x0f3fffff]
[KERNEL] [ 0.000000] [mem 0x08000000-0x0f3fffff] page 2M
[KERNEL] [ 0.000000] init_memory_mapping: [mem 0x00100000-0x07ffffff]
[KERNEL] [ 0.000000] [mem 0x00100000-0x003fffff] page 4k
[KERNEL] [ 0.000000] [mem 0x00400000-0x07ffffff] page 2M
[KERNEL] [ 0.000000] init_memory_mapping: [mem 0x0f800000-0x0ffebfff]
[KERNEL] [ 0.000000] [mem 0x0f800000-0x0fbfffff] page 2M
[KERNEL] [ 0.000000] [mem 0x0fc00000-0x0ffebfff] page 4k
[KERNEL] [ 0.000000] BRK [0x0050a000, 0x0050afff] PGTABLE
[KERNEL] [ 0.000000] early_memtest: # of tests: 1
[KERNEL] [ 0.000000] 0000010000 - 000009b000 pattern 0000000000000000
[KERNEL] [ 0.000000] 0000510000 - 000fbed000 pattern 0000000000000000
[KERNEL] [ 0.000000] 000fed3000 - 000ffec000 pattern 0000000000000000
[KERNEL] [ 0.000000] RAMDISK: [mem 0x0fbed000-0x0fed2fff]
[KERNEL] [ 0.000000] ACPI: RSDP 000f5b70 000014 (v00 ASUS )
[KERNEL] [ 0.000000] ACPI: RSDT 0ffec000 00002C (v01 ASUS CUV4X_M
30303031 MSFT 31313031)
[KERNEL] [ 0.000000] ACPI: FACP 0ffec080 000074 (v01 ASUS CUV4X_M
30303031 MSFT 31313031)
[KERNEL] [ 0.000000] ACPI: DSDT 0ffec100 00253C (v01 ASUS CUV4X_M
00001000 MSFT 0100000B)
[KERNEL] [ 0.000000] ACPI: FACS 0ffff000 000040
[KERNEL] [ 0.000000] ACPI: BOOT 0ffec040 000028 (v01 ASUS CUV4X_M
30303031 MSFT 31313031)
[KERNEL] [ 0.000000] 255MB LOWMEM available.
[KERNEL] [ 0.000000] mapped low ram: 0 - 0ffec000
[KERNEL] [ 0.000000] low ram: 0 - 0ffec000
[KERNEL] [ 0.000000] Zone ranges:
[KERNEL] [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[KERNEL] [ 0.000000] Normal [mem 0x01000000-0x0ffebfff]
[KERNEL] [ 0.000000] Movable zone start for each node
[KERNEL] [ 0.000000] Early memory node ranges
[KERNEL] [ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[KERNEL] [ 0.000000] node 0: [mem 0x00100000-0x0ffebfff]
[KERNEL] [ 0.000000] On node 0 totalpages: 65418
[KERNEL] [ 0.000000] free_area_init_node: node 0, pgdat c0479240,
node_mem_map cf9ed020
[KERNEL] [ 0.000000] DMA zone: 32 pages used for memmap
[KERNEL] [ 0.000000] DMA zone: 0 pages reserved
[KERNEL] [ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[KERNEL] [ 0.000000] Normal zone: 480 pages used for memmap
[KERNEL] [ 0.000000] Normal zone: 61420 pages, LIFO batch:15
[KERNEL] [ 0.000000] Using APIC driver default
[KERNEL] [ 0.000000] ACPI: PM-Timer IO Port: 0xe408
[KERNEL] [ 0.000000] Local APIC disabled by BIOS -- you can enable it
with "lapic"
[KERNEL] [ 0.000000] APIC: disable apic facility
[KERNEL] [ 0.000000] APIC: switched to apic NOOP
[KERNEL] [ 0.000000] nr_irqs_gsi: 16
[KERNEL] [ 0.000000] e820: [mem 0x10000000-0xfffeffff] available for PCI
devices
[KERNEL] [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[KERNEL] [ 0.000000] pcpu-alloc: [0] 0
[KERNEL] [ 0.000000] Built 1 zonelists in Zone order, mobility grouping
on. Total pages: 64906
[KERNEL] [ 0.000000] Kernel command line: root=/dev/ram0 memtest=1 quiet
initrd=packages/initrd BOOT_IMAGE=packages/kernel
[KERNEL] [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[KERNEL] [ 0.000000] Dentry cache hash table entries: 32768 (order: 5,
131072 bytes)
[KERNEL] [ 0.000000] Inode-cache hash table entries: 16384 (order: 4,
65536 bytes)
[KERNEL] [ 0.000000] Initializing CPU#0
[KERNEL] [ 0.000000] Memory: 252184K/261672K available (2627K kernel
code, 188K rwdata, 748K rodata, 312K init, 236K bss, 9488K reserved)
[KERNEL] [ 0.000000] virtual kernel memory layout:
[KERNEL] [ 0.000000] fixmap : 0xfffa2000 - 0xfffff000 ( 372 kB)
[KERNEL] [ 0.000000] vmalloc : 0xd07ec000 - 0xfffa0000 ( 759 MB)
[KERNEL] [ 0.000000] lowmem : 0xc0000000 - 0xcffec000 ( 255 MB)
[KERNEL] [ 0.000000] .init : 0xc047e000 - 0xc04cc000 ( 312 kB)
[KERNEL] [ 0.000000] .data : 0xc03912c0 - 0xc047d100 ( 943 kB)
[KERNEL] [ 0.000000] .text : 0xc0100000 - 0xc03912c0 (2628 kB)
[KERNEL] [ 0.000000] Checking if this processor honours the WP bit even
in supervisor mode...Ok.
[KERNEL] [ 0.000000] Preemptible hierarchical RCU implementation.
[KERNEL] [ 0.000000] NR_IRQS:2304 nr_irqs:256 16
[KERNEL] [ 0.000000] CPU 0 irqstacks, hard=cf406000 soft=cf408000
[KERNEL] [ 0.000000] Console: colour VGA+ 80x25
[KERNEL] [ 0.000000] console [tty0] enabled
[KERNEL] [ 0.000000] tsc: Fast TSC calibration using PIT
[KERNEL] [ 0.000000] tsc: Detected 731.511 MHz processor
[KERNEL] [ 0.001007] Calibrating delay loop (skipped), value calculated
using timer frequency.. 1463.02 BogoMIPS (lpj=731511)
[KERNEL] [ 0.001021] pid_max: default: 32768 minimum: 301
[KERNEL] [ 0.001138] Mount-cache hash table entries: 1024 (order: 0,
4096 bytes)
[KERNEL] [ 0.001148] Mountpoint-cache hash table entries: 1024 (order:
0, 4096 bytes)
[KERNEL] [ 0.002111] Last level iTLB entries: 4KB 32, 2MB 0, 4MB 2
[KERNEL] [ 0.002111] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 8
[KERNEL] [ 0.002111] tlb_flushall_shift: 6
[KERNEL] [ 0.002134] CPU: Intel Pentium III (Coppermine) (fam: 06,
model: 08, stepping: 06)
[KERNEL] [ 0.002316] ACPI: Core revision 20131115
[KERNEL] [ 0.006145] ACPI: All ACPI Tables successfully acquired
[KERNEL] [ 0.006165] ACPI: setting ELCR to 0200 (from 0c00)
[KERNEL] [ 0.006558] Performance Events:
[KERNEL] [ 0.006571] no APIC, boot with the "lapic" boot parameter to
force-enable it.
[KERNEL] [ 0.006578] no hardware sampling interrupt available.
[KERNEL] [ 0.006585] p6 PMU driver.
[KERNEL] [ 0.006595] ... version: 0
[KERNEL] [ 0.006601] ... bit width: 32
[KERNEL] [ 0.006606] ... generic registers: 2
[KERNEL] [ 0.006612] ... value mask: 00000000ffffffff
[KERNEL] [ 0.006617] ... max period: 000000007fffffff
[KERNEL] [ 0.006622] ... fixed-purpose events: 0
[KERNEL] [ 0.006627] ... event mask: 0000000000000003
[KERNEL] [ 0.007411] devtmpfs: initialized
[KERNEL] [ 0.008142] PM: Registering ACPI NVS region [mem
0x0ffff000-0x0fffffff] (4096 bytes)
[KERNEL] [ 0.008518] NET: Registered protocol family 16
[KERNEL] [ 0.009429] cpuidle: using governor ladder
[KERNEL] [ 0.009440] cpuidle: using governor menu
[KERNEL] [ 0.009556] ACPI: bus type PCI registered
[KERNEL] [ 0.011162] PCI: PCI BIOS revision 2.10 entry at 0xf0890, last
bus=1
[KERNEL] [ 0.011170] PCI: Using configuration type 1 for base access
[KERNEL] [ 0.019451] bio: create slab at 0
[KERNEL] [ 0.019912] ACPI: Added _OSI(Module Device)
[KERNEL] [ 0.019922] ACPI: Added _OSI(Processor Device)
[KERNEL] [ 0.019929] ACPI: Added _OSI(3.0 _SCP Extensions)
[KERNEL] [ 0.019937] ACPI: Added _OSI(Processor Aggregator Device)
[KERNEL] [ 0.026121] ACPI: Interpreter enabled
[KERNEL] [ 0.026191] ACPI Exception: AE_NOT_FOUND, While evaluating
Sleep State [\_S2_] (20131115/hwxface-580)
[KERNEL] [ 0.026207] ACPI Exception: AE_NOT_FOUND, While evaluating
Sleep State [\_S3_] (20131115/hwxface-580)
[KERNEL] [ 0.026232] ACPI: (supports S0 S1 S5)
[KERNEL] [ 0.026240] ACPI: Using PIC for interrupt routing
[KERNEL] [ 0.026438] PCI: Ignoring host bridge windows from ACPI; if
necessary, use "pci=use_crs" and report a bug
[KERNEL] [ 0.045040] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9
10 11 12 14 15) *0, disabled.
[KERNEL] [ 0.045311] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9
10 11 12 14 15) *0, disabled.
[KERNEL] [ 0.045593] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9
10 *11 12 14 15)
[KERNEL] [ 0.045873] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9
*10 11 12 14 15)
[KERNEL] [ 0.046179] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[KERNEL] [ 0.046202] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM
Segments]
[KERNEL] [ 0.046225] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND);
disabling ASPM
[KERNEL] [ 0.046610] acpi PNP0A03:00: host bridge window [io
0x0000-0x0cf7] (ignored)
[KERNEL] [ 0.046622] acpi PNP0A03:00: host bridge window [io
0x0d00-0xffff] (ignored)
[KERNEL] [ 0.046632] acpi PNP0A03:00: host bridge window [mem
0x000a0000-0x000bffff] (ignored)
[KERNEL] [ 0.046642] acpi PNP0A03:00: host bridge window [mem
0x000c8000-0x000dffff] (ignored)
[KERNEL] [ 0.046651] acpi PNP0A03:00: host bridge window [mem
0x10000000-0xffffffff] (ignored)
[KERNEL] [ 0.046660] PCI: root bus 00: using default resources
[KERNEL] [ 0.046671] acpi PNP0A03:00: fail to add MMCONFIG information,
can't access extended PCI configuration space under this bridge.
[KERNEL] [ 0.046879] PCI host bridge to bus 0000:00
[KERNEL] [ 0.046895] pci_bus 0000:00: root bus resource [bus 00-ff]
[KERNEL] [ 0.046905] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[KERNEL] [ 0.046915] pci_bus 0000:00: root bus resource [mem
0x00000000-0xffffffff]
[KERNEL] [ 0.046946] pci 0000:00:00.0: [1106:0691] type 00 class 0x060000
[KERNEL] [ 0.046971] pci 0000:00:00.0: reg 0x10: [mem
0xe4000000-0xe7ffffff pref]
[KERNEL] [ 0.047273] pci 0000:00:01.0: [1106:8598] type 01 class 0x060400
[KERNEL] [ 0.047319] pci 0000:00:01.0: supports D1
[KERNEL] [ 0.047504] pci 0000:00:04.0: [1106:0686] type 00 class 0x060100
[KERNEL] [ 0.047773] pci 0000:00:04.1: [1106:0571] type 00 class 0x01018a
[KERNEL] [ 0.047826] pci 0000:00:04.1: reg 0x20: [io 0xd800-0xd80f]
[KERNEL] [ 0.048108] pci 0000:00:04.2: [1106:3038] type 00 class 0x0c0300
[KERNEL] [ 0.048159] pci 0000:00:04.2: reg 0x20: [io 0xd400-0xd41f]
[KERNEL] [ 0.048276] pci 0000:00:04.2: System wakeup disabled by ACPI
[KERNEL] [ 0.048441] pci 0000:00:04.3: [1106:3038] type 00 class 0x0c0300
[KERNEL] [ 0.048491] pci 0000:00:04.3: reg 0x20: [io 0xd000-0xd01f]
[KERNEL] [ 0.048676] pci 0000:00:04.3: System wakeup disabled by ACPI
[KERNEL] [ 0.048842] pci 0000:00:04.4: [1106:3057] type 00 class 0x060000
[KERNEL] [ 0.048900] pci 0000:00:04.4: address space collision: [io
0xe400-0xe4ff] conflicts with ACPI CPU throttle [???
0x0000e410-0x0000e415 flags 0x80000000]
[KERNEL] [ 0.048915] pci 0000:00:04.4: quirk: [io 0xe800-0xe80f] claimed
by vt82c686 SMB
[KERNEL] [ 0.049184] pci 0000:00:04.5: [1106:3058] type 00 class 0x040100
[KERNEL] [ 0.049211] pci 0000:00:04.5: reg 0x10: [io 0xb800-0xb8ff]
[KERNEL] [ 0.049229] pci 0000:00:04.5: reg 0x14: [io 0xb400-0xb403]
[KERNEL] [ 0.049246] pci 0000:00:04.5: reg 0x18: [io 0xb000-0xb003]
[KERNEL] [ 0.049500] pci 0000:00:0a.0: [10ec:8139] type 00 class 0x020000
[KERNEL] [ 0.049525] pci 0000:00:0a.0: reg 0x10: [io 0xa800-0xa8ff]
[KERNEL] [ 0.049543] pci 0000:00:0a.0: reg 0x14: [mem 0xdb800000-0xdb8000ff]
[KERNEL] [ 0.049753] pci 0000:00:0a.0: reg 0x30: [mem
0x00000000-0x0000ffff pref]
[KERNEL] [ 0.049779] pci 0000:00:0a.0: supports D1 D2
[KERNEL] [ 0.049789] pci 0000:00:0a.0: PME# supported from D1 D2 D3hot
D3cold
[KERNEL] [ 0.050203] pci 0000:01:00.0: [5333:8a13] type 00 class 0x030000
[KERNEL] [ 0.050230] pci 0000:01:00.0: reg 0x10: [mem 0xdc000000-0xdfffffff]
[KERNEL] [ 0.050276] pci 0000:01:00.0: reg 0x30: [mem
0xe3ff0000-0xe3ffffff pref]
[KERNEL] [ 0.050304] pci 0000:01:00.0: supports D1 D2
[KERNEL] [ 0.050470] pci 0000:00:01.0: PCI bridge to [bus 01]
[KERNEL] [ 0.050487] pci 0000:00:01.0: bridge window [mem
0xdc000000-0xe3dfffff]
[KERNEL] [ 0.050498] pci 0000:00:01.0: bridge window [mem
0xe3f00000-0xe3ffffff pref]
[KERNEL] [ 0.050515] pci_bus 0000:00: on NUMA node 0
[KERNEL] [ 0.053419] ACPI: \_SB_.PCI0: notify handler is installed
[KERNEL] [ 0.053487] Found 1 acpi root devices
[KERNEL] [ 0.053774] ACPI: bus type USB registered
[KERNEL] [ 0.053959] usbcore: registered new interface driver usbfs
[KERNEL] [ 0.054126] usbcore: registered new interface driver hub
[KERNEL] [ 0.054255] usbcore: registered new device driver usb
[KERNEL] [ 0.054796] wmi: Mapper loaded
[KERNEL] [ 0.054806] PCI: Using ACPI for IRQ routing
[KERNEL] [ 0.054817] PCI: pci_cache_line_size set to 32 bytes
[KERNEL] [ 0.054865] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[KERNEL] [ 0.054875] e820: reserve RAM buffer [mem 0x0ffec000-0x0fffffff]
[KERNEL] [ 0.055547] Switched to clocksource pit
[KERNEL] [ 0.055903] pnp: PnP ACPI init
[KERNEL] [ 0.055930] ACPI: bus type PNP registered
[KERNEL] [ 0.056017] system 00:00: [mem 0x00000000-0x0009ffff] could not
be reserved
[KERNEL] [ 0.056033] system 00:00: [mem 0x000f0000-0x000fffff] could not
be reserved
[KERNEL] [ 0.056045] system 00:00: [mem 0x00100000-0x0fffffff] could not
be reserved
[KERNEL] [ 0.056056] system 00:00: [mem 0xfffe0000-0xffffffff] could not
be reserved
[KERNEL] [ 0.056069] system 00:00: Plug and Play ACPI device, IDs
PNP0c01 (active)
[KERNEL] [ 0.056859] system 00:01: [io 0x03f0-0x03f1] has been reserved
[KERNEL] [ 0.056874] system 00:01: [io 0x04d0-0x04d1] has been reserved
[KERNEL] [ 0.056886] system 00:01: Plug and Play ACPI device, IDs
PNP0c02 (active)
[KERNEL] [ 0.056989] pnp 00:02: disabling [io 0xe400-0xe47f] because it
overlaps 0000:00:04.4 BAR 7 [io 0xe400-0xe4ff]
[KERNEL] [ 0.057141] system 00:02: [io 0xe800-0xe80f] has been reserved
[KERNEL] [ 0.057154] system 00:02: Plug and Play ACPI device, IDs
PNP0c02 (active)
[KERNEL] [ 0.057337] pnp 00:03: [dma 4]
[KERNEL] [ 0.057563] pnp 00:03: Plug and Play ACPI device, IDs PNP0200
(active)
[KERNEL] [ 0.057746] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00
(active)
[KERNEL] [ 0.057914] pnp 00:05: Plug and Play ACPI device, IDs PNP0800
(active)
[KERNEL] [ 0.058077] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04
(active)
[KERNEL] [ 0.058753] pnp 00:07: [dma 2]
[KERNEL] [ 0.058974] pnp 00:07: Plug and Play ACPI device, IDs PNP0700
(active)
[KERNEL] [ 0.060556] pnp 00:08: [dma 3]
[KERNEL] [ 0.060836] pnp 00:08: Plug and Play ACPI device, IDs PNP0401
(active)
[KERNEL] [ 0.062207] pnp 00:09: Plug and Play ACPI device, IDs PNP0501
(active)
[KERNEL] [ 0.063534] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501
(active)
[KERNEL] [ 0.064088] pnp 00:0b: Plug and Play ACPI device, IDs PNP0303
(active)
[KERNEL] [ 0.064382] pnp: PnP ACPI: found 12 devices
[KERNEL] [ 0.064389] ACPI: bus type PNP unregistered
[KERNEL] [ 0.110117] Switched to clocksource acpi_pm
[KERNEL] [ 0.110189] pci 0000:00:0a.0: BAR 6: assigned [mem
0x10000000-0x1000ffff pref]
[KERNEL] [ 0.110205] pci 0000:00:01.0: PCI bridge to [bus 01]
[KERNEL] [ 0.110220] pci 0000:00:01.0: bridge window [mem
0xdc000000-0xe3dfffff]
[KERNEL] [ 0.110232] pci 0000:00:01.0: bridge window [mem
0xe3f00000-0xe3ffffff pref]
[KERNEL] [ 0.110248] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[KERNEL] [ 0.110257] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[KERNEL] [ 0.110268] pci_bus 0000:01: resource 1 [mem 0xdc000000-0xe3dfffff]
[KERNEL] [ 0.110278] pci_bus 0000:01: resource 2 [mem
0xe3f00000-0xe3ffffff pref]
[KERNEL] [ 0.110372] NET: Registered protocol family 2
[KERNEL] [ 0.110858] TCP established hash table entries: 2048 (order: 1,
8192 bytes)
[KERNEL] [ 0.110895] TCP bind hash table entries: 2048 (order: 1, 8192
bytes)
[KERNEL] [ 0.110927] TCP: Hash tables configured (established 2048 bind
2048)
[KERNEL] [ 0.110998] TCP: reno registered
[KERNEL] [ 0.111009] UDP hash table entries: 256 (order: 0, 4096 bytes)
[KERNEL] [ 0.111030] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[KERNEL] [ 0.111161] NET: Registered protocol family 1
[KERNEL] [ 0.111215] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[KERNEL] [ 0.111231] pci 0000:00:04.0: Disabling VIA external APIC routing
[KERNEL] [ 0.112483] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
[KERNEL] [ 0.112494] PCI: setting IRQ 10 as level-triggered
[KERNEL] [ 0.113368] pci 0000:01:00.0: Boot video device
[KERNEL] [ 0.113378] PCI: CLS 32 bytes, default 32
[KERNEL] [ 0.139831] Freeing initrd memory: 2968K (cfbed000 - cfed3000)
[KERNEL] [ 0.139979] Simple Boot Flag at 0x3a set to 0x1
[KERNEL] [ 0.142514] ROMFS MTD (C) 2007 Red Hat, Inc.
[KERNEL] [ 0.142547] msgmni has been set to 498
[KERNEL] [ 0.143046] io scheduler noop registered
[KERNEL] [ 0.143064] io scheduler cfq registered (default)
[KERNEL] [ 0.143580] intel_idle: does not run on family 6 model 8
[KERNEL] [ 0.143819] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[KERNEL] [ 0.143835] ACPI: Power Button [PWRB]
[KERNEL] [ 0.144063] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[KERNEL] [ 0.144074] ACPI: Power Button [PWRF]
[KERNEL] [ 0.144300] tsc: Marking TSC unstable due to TSC halts in idle
[KERNEL] [ 0.144318] ACPI: acpi_idle registered with cpuidle
[KERNEL] [ 0.145251] brd: module loaded
[KERNEL] [ 0.145276] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[KERNEL] [ 0.145282] ehci-pci: EHCI PCI platform driver
[KERNEL] [ 0.145390] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[KERNEL] [ 0.145397] ohci-pci: OHCI PCI platform driver
[KERNEL] [ 0.145556] uhci_hcd: USB Universal Host Controller Interface
driver
[KERNEL] [ 0.146036] uhci_hcd 0000:00:04.2: UHCI Host Controller
[KERNEL] [ 0.146062] uhci_hcd 0000:00:04.2: new USB bus registered,
assigned bus number 1
[KERNEL] [ 0.146115] uhci_hcd 0000:00:04.2: irq 10, io base 0x0000d400
[KERNEL] [ 0.146301] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0001
[KERNEL] [ 0.146312] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[KERNEL] [ 0.146321] usb usb1: Product: UHCI Host Controller
[KERNEL] [ 0.146330] usb usb1: Manufacturer: Linux 3.13.11 uhci_hcd
[KERNEL] [ 0.146338] usb usb1: SerialNumber: 0000:00:04.2
[KERNEL] [ 0.146925] hub 1-0:1.0: USB hub found
[KERNEL] [ 0.146957] hub 1-0:1.0: 2 ports detected
[KERNEL] [ 0.147614] uhci_hcd 0000:00:04.3: UHCI Host Controller
[KERNEL] [ 0.147639] uhci_hcd 0000:00:04.3: new USB bus registered,
assigned bus number 2
[KERNEL] [ 0.147684] uhci_hcd 0000:00:04.3: irq 10, io base 0x0000d000
[KERNEL] [ 0.147858] usb usb2: New USB device found, idVendor=1d6b,
idProduct=0001
[KERNEL] [ 0.147868] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[KERNEL] [ 0.147878] usb usb2: Product: UHCI Host Controller
[KERNEL] [ 0.147886] usb usb2: Manufacturer: Linux 3.13.11 uhci_hcd
[KERNEL] [ 0.147894] usb usb2: SerialNumber: 0000:00:04.3
[KERNEL] [ 0.148379] hub 2-0:1.0: USB hub found
[KERNEL] [ 0.148407] hub 2-0:1.0: 2 ports detected
[KERNEL] [ 0.149102] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at
0x60,0x64 irq 1
[KERNEL] [ 0.149113] i8042: PNP: PS/2 appears to have AUX port disabled,
if this is incorrect please boot with i8042.nopnp
[KERNEL] [ 0.149493] serio: i8042 KBD port at 0x60,0x64 irq 1
[KERNEL] [ 0.149676] hv_vmbus: registering driver hyperv_keyboard
[KERNEL] [ 0.149910] mousedev: PS/2 mouse device common for all mice
[KERNEL] [ 0.150837] input: PC Speaker as
/devices/platform/pcspkr/input/input3
[KERNEL] [ 0.151240] hidraw: raw HID events driver (C) Jiri Kosina
[KERNEL] [ 0.151949] hv_vmbus: registering driver hid_hyperv
[KERNEL] [ 0.153075] usbcore: registered new interface driver usbhid
[KERNEL] [ 0.153086] usbhid: USB HID core driver
[KERNEL] [ 0.153571] zram: Created 1 device(s) ...
[KERNEL] [ 0.153770] TCP: cubic registered
[KERNEL] [ 0.153780] NET: Registered protocol family 17
[KERNEL] [ 0.153913] Using IPI Shortcut mode
[KERNEL] [ 0.173202] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input2
[KERNEL] [ 0.173523] RAMDISK: xz image found at block 0
[KERNEL] [ 0.448508] usb 1-1: new low-speed USB device number 2 using
uhci_hcd
[KERNEL] [ 0.608190] usb 1-1: New USB device found, idVendor=09da,
idProduct=000a
[KERNEL] [ 0.608210] usb 1-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[KERNEL] [ 0.608219] usb 1-1: Product: USB Mouse
[KERNEL] [ 0.608228] usb 1-1: Manufacturer: A4Tech
[KERNEL] [ 0.636501] input: A4Tech USB Mouse as
/devices/pci0000:00/0000:00:04.2/usb1/1-1/1-1:1.0/input/input4
[KERNEL] [ 0.642450] a4tech 0003:09DA:000A.0001: input,hidraw0: USB HID
v1.10 Mouse [A4Tech USB Mouse] on usb-0000:00:04.2-1/input0
[KERNEL] [ 1.902239] VFS: Mounted root (romfs filesystem) readonly on
device 1:0.
[KERNEL] [ 1.902391] devtmpfs: mounted
[KERNEL] [ 1.903177] Freeing unused kernel memory: 312K (c047e000 -
c04cc000)
[KERNEL] [ 1.903512] Write protecting the kernel text: 2632k
[KERNEL] [ 1.903565] Write protecting the kernel read-only data: 752k
[pfac] Ok, PID 393.
[initrd] WTware shell v.5.1.64
[initrd] PCI: C 06 1106:0691 Bridge VIA Technologies, Inc.
VT82C693A/694x [Apollo PRO133x].
[initrd] PCI: C 06:04 1106:8598 Bridge PCI bridge VIA Technologies, Inc.
VT82C598/694x [Apollo MVP3/Pro133x AGP].
[initrd] PCI: C 06:01 1106:0686 Bridge ISA bridge VIA Technologies, Inc.
VT82C686 [Apollo Super South].
[initrd] PCI: C 01:01 1106:0571 Mass storage controller IDE interface
VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus
Master IDE.
[initrd] PCI: C 0c:03 1106:3038 Serial bus controller USB controller VIA
Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller.
[initrd] PCI: C 06 1106:3057 Bridge VIA Technologies, Inc. VT82C686
[Apollo Super ACPI].
[initrd] PCI: C 04:01 1106:3058 Multimedia controller Multimedia audio
controller VIA Technologies, Inc. VT82C686 AC97 Audio Controller.
[initrd] PCI: C 02 10ec:8139 Network controller Realtek Semiconductor
Co., Ltd. RTL-8139/8139C/8139C+.
[initrd] PCI: C 03 5333:8a13 Display controller S3 Graphics Ltd. 86c360
[Trio 3D/1X], 86c362, 86c368 [Trio 3D/2X].
[initrd] USB: 09da:000a A4 Tech Co., Ltd Optical Mouse Opto 510D.
[initrd] Load ethernet drivers.
[initrd] modprobe 8139too.
[KERNEL] [ 2.780121] 8139too: 8139too Fast Ethernet driver 0.9.28
[KERNEL] [ 2.780231] 8139too 0000:00:0a.0: enabling device (0005 -> 0007)
[KERNEL] [ 2.781445] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[KERNEL] [ 2.781456] PCI: setting IRQ 11 as level-triggered
[KERNEL] [ 2.788156] 8139too 0000:00:0a.0 eth0: RealTek RTL8139 at
0x0001a800, 00:80:48:29:9e:91, IRQ 11
[initrd] NIC module 8139too.ko loaded.
[initrd] modprobe 8139cp.
[KERNEL] [ 2.800707] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3
(Mar 22, 2004)
[initrd] NIC module 8139cp.ko loaded.
[initrd] eth0: 10ec:8139. Apply WOL configuration.
[KERNEL] [ 2.822909] 8139too 0000:00:0a.0 eth0: link up, 100Mbps,
full-duplex, lpa 0x45E1
[initrd] dhcp: 343 bytes from 192.168.0.1.
[initrd]
00000000:000001430000000000110000c0a80001c0a8000d004300440143000002010600 ...C................C.D.C......
[initrd]
00000020:67458b6b0000000000000000c0a8000dc0a8000100000000008048299e910000 gE.k......................H)....
[initrd]
00000040:0000000000000000000000000000000000000000000000000000000000000000 ................................
[initrd]
00000060:0000000000000000000000000000000000000000000000000000000000000000 ................................
[initrd] dhcp-client.cpp ( 508), recvACK: -- ERROR -- INTERNAL ERROR.
Please, contact WTware tech support.
[initrd] dhcp: 343 bytes from 192.168.0.1.
[initrd]
00000000:000001430000000000110000c0a80001c0a8000d004300440143000002010600 ...C................C.D.C......
[initrd]
00000020:67458b6b0000000000000000c0a8000dc0a8000100000000008048299e910000 gE.k......................H)....
[initrd]
00000040:0000000000000000000000000000000000000000000000000000000000000000 ................................
[initrd]
00000060:0000000000000000000000000000000000000000000000000000000000000000 ................................
[initrd] dhcp: server address 192.168.0.1.
[initrd] dhcp: 192.168.0.13/255.255.255.0.
[initrd] dhcp: default gateway 192.168.0.1.
[initrd] dhcp: DNS 192.168.0.5.
[initrd] dhcp: DNS 192.168.0.6.
[initrd] dhcp: hostname wt5client2.
[initrd] dhcp: domain futu.local.
[initrd] dhcp: TFTP 192.168.0.1.
[initrd] dhcp: boot file (header) wtware.net/5.1.64/wtware.pxe.
[initrd] TFTP binary "wtware.net/5.1.64/", configs prefix "wtware.net/",
using "/" slash.
Send broadcast WTCU discover.
[initrd] TFTP: download file wtware.net/Everyone/list.wtc from 192.168.0.1.
[initrd] It isn't WTware5 TFTP server...
/--- FILE "/tmp/list.wtc" -----------------------
| #
| # Ñïèñîê ïîäêëþ÷àåìûõ ôàéëîâ.
| #
| # Ýòîò îòäåëüíûé ìåõàíèçì íàñòðîéêè òåðìèíàëîâ ïðåäíàçíà÷åí òîëüêî
| # äëÿ ðó÷íîãî êîíôèãóðèðîâàíèÿ òåðìèíàëîâ. Ãðàôè÷åñêèé êîíôèãóðàòîð
| # íå ÷èòàåò list.wtc, íå ÷èòàåò è íå ïîçâîëÿåò ðåäàêòèðîâàòü ôàéëû
| # èç êàòàëîãà ListIncludes. Ïîýòîìó íåëüçÿ ïûòàòüñÿ íàñòðàèâàòü îäèí
| # è òîò æå òåðìèíàë è êîíôèãóðàòîðîì, è ÷åðåç list.wtc.
| #
| # Ôîðìàò ñòðîêè â ýòîì ôàéëå:
| #
| # 01.02.03.04.05.06[([èìÿïîëüçîâàòåëÿ@][èìÿòåðìèíàëà])] [ôàéë [ôàéë
...]]] [# êîììåíòàðèé]
| #
| # Ïðèìåðû:
| #
| # 02.03.04.05.06.07 file1
| #
| # Îçíà÷àåò, ÷òî òåðìèíàë ñ ìàê-àäðåñîì 02.03.04.05.06.07 ïðî÷èòàåò
| # ïàðàìåòðû èç ôàéëà ListIncludes/file1.
| #
| #
| # 03.04.05.06.07.08(vasja@) file2
| #
| # Îçíà÷àåò, ÷òî òåðìèíàë ñ ìàê-àäðåñîì 03.04.05.06.07.08 ïðî÷èòàåò
| # ïàðàìåòðû èç ôàéëà ListIncludes/file2 è â îêîøêî "Âõîä â Windows"
| # ïîäñòàâèò èìÿ ïîëüçîâàòåëÿ "vasja".
| #
| #
| # 04.05.06.07.08.09(term5) file6 file7 # Êîìï çàìãëàâáóõà.
| #
| # Îçíà÷àåò, ÷òî òåðìèíàëó ñ ìàê-àäðåñîì 04.05.06.07.08.09 áóäåò
| # ïðèñâîåíî èìÿ term5, àíàëîãè÷íî óêàçàíèþ ïàðàìåòðà clienthostname,
| # è îí ïðî÷èòàåò ïàðàìåòðû èç ôàéëîâ ListIncludes/file6 è
| # ListIncludes/file7.
| #
| #
| # ×òîáû ìîæíî áûëî óêàçûâàòü èìÿ ïîëüçîâàòåëÿ ðóññêèìè áóêâàìè, íàäî
| # îòêðûòü ýòîò ôàéë â Notepad è ñîõðàíèòü ñ Encoding: Unicode.
| #
\----------------------------------------------------
[initrd] TFTP: download file
wtware.net/Terminals/00.80.48.29.9E.91/config.wtc from 192.168.0.1.
/--- FILE "/tmp/config.wtc" -----------------------
| #
| # Êîíôèãóðàöèîííûé ôàéë òåðìèíàëà. Îí íàõîäèòñÿ â êàòàëîãå
| #
| # Terminals\00.80.48.29.9E.91\
| #
| # Ýòîò ôàéë ïðî÷èòàåò òåðìèíàë ñ ÌÀÊ-àäðåñîì 00.80.48.29.9E.91
| #
| # Åñëè òåðìèíàë íå íàéäåò ñâîé êîíôèãóðàöèîííûé ôàéë, îí
| # ïðåäëîæèò ïðîâåñòè íàñòðîéêó âèäåîêàðòû è íå ñòàíåò ïîäêëþ÷àòüñÿ
| # ê òåðìèíàëüíîìó ñåðâåðó.
| #
| # Êîíôèãóðàöèîíûíé ôàéë íàäî ñîçäàâàòü âðó÷íóþ. Ïîä Windows ìîæíî
| # óñòàíîâèòü wtware èç .exe-äèñòðèáóòèâà è ïîëüçîâàòüñÿ ãðàôè÷åñêèì
| # êîíôèãóðàòîðîì äëÿ ñîçäàíèÿ êîíôèãóðàöèîííûõ ôàéëîâ.
| #
| #
| # Îáÿçàòåëüíî íàäî óêàçàòü, ê êàêîìó ñåðâåðó ïîäêëþ÷àòüñÿ:
| #
| #server = 192.168.1.1
| #
| # Ðàçðåøíèå ýêðàíà. Äëÿ LCD-ìîíèòîðîâ íàäî óêàçàòü ðàçðåøåíèå
| # ìàòðèöû. Ëþáûå äðóãèå ðàçðåøåíèÿ áóäóò ðàáîòàòü õóæå èëè íå áóäóò
| # ðàáîòàòü âîîáùå.
| #
| resolution = 1024x768
| refresh = 75
| #win2kIP = term16
| #user = newbie:newbie
| #domain = futu
| #keyboard = ru
| mouse_accel_mult = 1
| sound=on
| sound_level=100
| sound_control=sw
| microphone=on
| microphone_level=100
| turnoffmenu = on
| #autoshutdown = 60
| managed = on
| SIP=222:wt5client2@192.168.0.4
| shared_usb = on
| disk = cdrom;usb(r/o)
| # printer = usb
\----------------------------------------------------
[initrd] TFTP: download file wtware.net/Everyone/all.wtc from 192.168.0.1.
/--- FILE "/tmp/all.wtc" -----------------------
| #
| # Îáùåñèñòåìíûé êîíôèãóðàöèîííûé ôàéë. Ñþäà óäîáíî çàïèñûâàòü
| # òå ïàðàìåòðû, êîòîðûå èìåþò îäèíàêîâûå çíà÷åíèÿ äëÿ âñåõ
| # òåðìèíàëîâ.
| #
| # Íàïðèìåð, åñëè ó âàñ òîëüêî îäèí òåðìèíàëüíûé ñåðâåð, â ýòîì ôàéëå
| # íàäî íàïèñàòü:
| #
| # server=1.2.3.4
| #
| # Âìåñòî 1.2.3.4 óêàçàòü IP âàøåãî òåðìèíàëüíîãî ñåðâåðà. Âñå
| # òåðìèíàëû áóäóò çíàòü, êóäà èì ïîäêëþ÷àòüñÿ.
| #
| server=192.168.0.30
| domain = futu
| keyboard = ru
\----------------------------------------------------
[initrd] TFTP: download file wtware.net/Everyone/wtware.lic from
192.168.0.1.
/--- FILE "/etc/config.compiled" -----------------------
| [BOM]
| server=192.168.0.30
| domain=futu
| keyboard=ru
| resolution=1024x768
| refresh=75
| mouse_accel_mult=1
| sound=on
| sound_level=100
| sound_control=sw
| microphone=on
| microphone_level=100
| turnoffmenu=on
| managed=on
| SIP=222:wt5client2@192.168.0.4
| shared_usb=on
| disk=cdrom;usb(r/o)
| connection
\----------------------------------------------------
[initrd] Hostname: "wt5client2".
RSH: listener is active.
Everyone can control terminal by HTTP.
[initrd] TFTP: download and unpack file wtware.net/5.1.64/packages/lib6
from 192.168.0.1.
[KERNEL] [ 5.118308] random: nonblocking pool is initialized
[initrd] Use 'video=VESA(F)' driver.
/--- FILE "/etc/config.compiled" -----------------------
| [BOM]
| server=192.168.0.30
| domain=futu
| keyboard=ru
| resolution=1024x768
| refresh=75
| mouse_accel_mult=1
| sound=on
| sound_level=100
| sound_control=sw
| microphone=on
| microphone_level=100
| turnoffmenu=on
| managed=on
| SIP=222:wt5client2@192.168.0.4
| shared_usb=on
| disk=cdrom;usb(r/o)
| video=VESA(F)
| connection
\----------------------------------------------------
[initrd] TFTP: download and unpack file wtware.net/5.1.64/packages/fwt
from 192.168.0.1.
[initrd] TFTP: download and unpack file wtware.net/5.1.64/packages/f
from 192.168.0.1.
[initrd] TFTP: download and unpack file
wtware.net/5.1.64/packages/graphic from 192.168.0.1.
[gm] WTware session manager v.5.1.64.
[gm] EV_REL flag found. Add mouse event4: A4Tech USB Mouse.
[gm] Add keyboard event3: AT Translated Set 2 keyboard.
[gm] Ignore event2: PC Speaker.
[gm] Add keyboard event1: Power Button.
[gm] Add keyboard event0: Power Button.
[gm] Display mode: 1024x768, 16 bit, 75 Hz, modeline "", DDC enabled,
connector 0.
[gm] VBE Version 2.0.
[gm] VBE modelist at 0x000c0b8b.
[gm] Mode 302: 320x200 (256 color palette) linelength 320 bits 8.
[gm] Mode 269: 320x200 (5:5:5) linelength 640 bits 15.
[gm] Mode 270: 320x200 (5:6:5) linelength 640 bits 16.
[gm] Mode 296: 320x200 (8:8:8) linelength 960 bits 24.
[gm] Mode 271: 320x200 (8:8:8) linelength 1280 bits 32.
[gm] Mode 305: 320x240 (256 color palette) linelength 320 bits 8.
[gm] Mode 306: 320x240 (5:5:5) linelength 640 bits 15.
[gm] Mode 307: 320x240 (5:6:5) linelength 640 bits 16.
[gm] Mode 309: 320x240 (8:8:8) linelength 960 bits 24.
[gm] Mode 308: 320x240 (8:8:8) linelength 1280 bits 32.
[gm] Mode 321: 400x300 (256 color palette) linelength 400 bits 8.
[gm] Mode 322: 400x300 (5:5:5) linelength 800 bits 15.
[gm] Mode 323: 400x300 (5:6:5) linelength 800 bits 16.
[gm] Mode 325: 400x300 (8:8:8) linelength 1200 bits 24.
[gm] Mode 324: 400x300 (8:8:8) linelength 1600 bits 32.
[gm] Mode 337: 512x384 (256 color palette) linelength 512 bits 8.
[gm] Mode 338: 512x384 (5:5:5) linelength 1024 bits 15.
[gm] Mode 339: 512x384 (5:6:5) linelength 1024 bits 16.
[gm] Mode 341: 512x384 (8:8:8) linelength 1536 bits 24.
[gm] Mode 340: 512x384 (8:8:8) linelength 2048 bits 32.
[gm] Mode 256: 640x400 (256 color palette) linelength 640 bits 8.
[gm] Mode 284: 640x400 (5:5:5) linelength 1280 bits 15.
[gm] Mode 285: 640x400 (5:6:5) linelength 1280 bits 16.
[gm] Mode 297: 640x400 (8:8:8) linelength 1920 bits 24.
[gm] Mode 286: 640x400 (8:8:8) linelength 2560 bits 32.
[gm] Mode 257: 640x480 (256 color palette) linelength 640 bits 8.
[gm] Mode 272: 640x480 (5:5:5) linelength 1280 bits 15.
[gm] Mode 273: 640x480 (5:6:5) linelength 1280 bits 16.
[gm] Mode 298: 640x480 (8:8:8) linelength 1920 bits 24.
[gm] Mode 274: 640x480 (8:8:8) linelength 2560 bits 32.
[gm] Mode 369: 720x480 (256 color palette) linelength 720 bits 8.
[gm] Mode 370: 720x480 (5:5:5) linelength 1440 bits 15.
[gm] Mode 371: 720x480 (5:6:5) linelength 1440 bits 16.
[gm] Mode 380: 720x576 (256 color palette) linelength 720 bits 8.
[gm] Mode 381: 720x576 (5:5:5) linelength 1440 bits 15.
[gm] Mode 382: 720x576 (5:6:5) linelength 1440 bits 16.
[gm] Mode 259: 800x600 (256 color palette) linelength 800 bits 8.
[gm] Mode 275: 800x600 (5:5:5) linelength 1600 bits 15.
[gm] Mode 276: 800x600 (5:6:5) linelength 1600 bits 16.
[gm] Mode 299: 800x600 (8:8:8) linelength 2400 bits 24.
[gm] Mode 277: 800x600 (8:8:8) linelength 3200 bits 32.
[gm] Mode 261: 1024x768 (256 color palette) linelength 1024 bits 8.
[gm] Mode 278: 1024x768 (5:5:5) linelength 2048 bits 15.
[gm] Mode 279: 1024x768 (5:6:5) linelength 2048 bits 16.
[gm] Use mode 279.
[gm] Mode 300: 1024x768 (8:8:8) linelength 3072 bits 24.
[gm] Mode 280: 1024x768 (8:8:8) linelength 4096 bits 32.
[gm] Mode 353: 1152x864 (256 color palette) linelength 1152 bits 8.
[gm] Mode 354: 1152x864 (5:5:5) linelength 2304 bits 15.
[gm] Mode 355: 1152x864 (5:6:5) linelength 2304 bits 16.
[gm] Mode 357: 1152x864 (8:8:8) linelength 3456 bits 24.
[gm] Mode 356: 1152x864 (8:8:8) linelength 4608 bits 32.
[gm] Mode 263: 1280x1024 (256 color palette) linelength 1280 bits 8.
[gm] Mode 281: 1280x1024 (5:5:5) linelength 2560 bits 15.
[gm] Mode 282: 1280x1024 (5:6:5) linelength 2560 bits 16.
[gm] Mode 301: 1280x1024 (8:8:8) linelength 3840 bits 24.
[gm] Mode 288: 1600x1200 (256 color palette) linelength 1600 bits 8.
[gm] Mode 289: 1600x1200 (5:5:5) linelength 3200 bits 15.
[gm] Mode 290: 1600x1200 (5:6:5) linelength 3200 bits 16.
[gm] Linear framebuffer.
[gm] mmap () return 0xb73a4000. Touch video memory.
[gm] Ok.
[gm] WMEMCOPY: 14400K copied in 170001 usec.
[gm] libc: 14400K copied in 170302 usec.
[gm] movs: 14400K copied in 170527 usec.
[gm] MMX: 14400K copied in 124430 usec.
[gm] Choose MMX memcpy.
[gm] TFTP: download and unpack file wtware.net/5.1.64/packages/alsa from
192.168.0.1.
[gm] It isn't WTware5 TFTP server...
[gm] TFTP: download and unpack file wtware.net/5.1.64/packages/alsalib
from 192.168.0.1.
[gm] TFTP: download and unpack file wtware.net/5.1.64/packages/alsalib6
from 192.168.0.1.
[gm] modprobe snd-via82xx.
[gm] ALSA module snd-via82xx.ko loaded.
[gm] modprobe snd-usb-audio.
/--- FILE "/proc/asound/devices" -----------------------
| 2: [ 0- 0]: digital audio playback
| 3: [ 0- 0]: digital audio capture
| 4: [ 0] : control
| 33: : timer
\----------------------------------------------------
[KERNEL] [ 12.000755] usbcore: registered new interface driver snd-usb-audio
[pfac] Got command line /sbin/rdpsnd 0 0 100 0 -1.
[gm] /dev/snd/controlC0 character device.
[pfac] Ok, PID 440.
[gm] /dev/snd/pcmC0D0c character device.
[pfac] Got command line /sbin/rdpaudin 0 100 0 -1.
[gm] /dev/snd/pcmC0D0p character device.
[pfac] Ok, PID 441.
[gm] /dev/snd/timer character device.
[gm] Run sound daemon.
[gm] Run microphone daemon.
/--- FILE "/.linphonerc" -----------------------
| [net]
| adaptive_rate_control=1
| mtu=0
| [audio_codec_0]
| mime=speex
| rate=32000
| enabled=1
| [audio_codec_1]
| mime=speex
| rate=16000
| enabled=1
| [audio_codec_2]
| mime=speex
| rate=8000
| enabled=1
| [audio_codec_3]
| mime=G729
| rate=8000
| enabled=1
| [audio_codec_4]
| mime=PCMU
| rate=8000
| enabled=1
| [audio_codec_5]
| mime=PCMA
| rate=8000
| enabled=1
| [audio_codec_6]
| mime=L16
| rate=44100
| enabled=0
| [audio_codec_7]
| mime=L16
| rate=44100
| enabled=0
| [audio_codec_8]
| mime=G722
| rate=8000
| enabled=0
| [sound]
| echocancellation=1
| ringer_dev_id=ALSA: VIA 82C686A/B rev20
| playback_dev_id=ALSA: VIA 82C686A/B rev20
| capture_dev_id=ALSA: VIA 82C686A/B rev20
| remote_ring=/usr/local/share/sounds/linphone/rings/ringback.wav
| local_ring=/usr/loca/share/sounds/linphone/rings/oldphone.wav
\----------------------------------------------------
[pfac] Got command line /sbin/rdpsnd sndvol 100 100 50.
[gm] Configure ALSA for SIP.
[pfac] Ok, PID 442.
[gm] TFTP: download and unpack file wtware.net/5.1.64/packages/linphone
from 192.168.0.1.
[rdpsnd] RDP Sound Redirector, WTware v.5.1.64.
[rdpaudin] RDP Microphone Redirector, WTware v.5.1.64.
[rdpaudin] Card 'rev20'/'VIA 82C686A/B rev20 with AD1881A at 0xb800, irq
11'.
[rdpaudin] Mixer name: 'Analog Devices AD1881A'.
[rdpaudin] Components: 'AC97a:41445348'.
[rdpaudin] Controls: 31.
[rdpaudin] ALSA: control 'Master Playback Switch'.
[rdpaudin] ALSA: control 'Master Playback Volume'.
[rdpaudin] ALSA: control 'Master Mono Playback Switch'.
[rdpaudin] ALSA: control 'Master Mono Playback Volume'.
[rdpaudin] ALSA: control 'Beep Playback Switch'.
[rdpaudin] ALSA: control 'Beep Playback Volume'.
[rdpaudin] ALSA: control 'Phone Playback Switch'.
[rdpaudin] ALSA: control 'Phone Playback Volume'.
[rdpaudin] ALSA: control 'Mic Playback Switch'.
[rdpaudin] ALSA: control 'Mic Playback Volume'.
[rdpaudin] ALSA: control 'Mic Boost (+20dB)'.
[rdpaudin] ALSA: control 'Line Playback Switch'.
[rdpaudin] ALSA: control 'Line Playback Volume'.
[rdpaudin] ALSA: control 'CD Playback Switch'.
[rdpaudin] ALSA: control 'CD Playback Volume'.
[rdpaudin] ALSA: control 'Video Playback Switch'.
[rdpaudin] ALSA: control 'Video Playback Volume'.
[rdpaudin] ALSA: control 'Aux Playback Switch'.
[rdpaudin] ALSA: control 'Aux Playback Volume'.
[rdpaudin] ALSA: control 'PCM Playback Switch'.
[rdpaudin] ALSA: control 'PCM Playback Volume'.
[rdpaudin] ALSA: control 'Capture Source'.
[rdpaudin] Capture Source [0] 'Mic'.
[rdpaudin] Capture Source [1] 'CD'.
[rdpaudin] Capture Source [2] 'Video'.
[rdpaudin] Capture Source [3] 'Aux'.
[rdpaudin] Capture Source [4] 'Line'.
[rdpaudin] Capture Source [5] 'Mix'.
[rdpaudin] Capture Source [6] 'Mix Mono'.
[rdpaudin] Capture Source [7] 'Phone'.
[rdpaudin] ALSA: control 'Capture Switch'.
[rdpaudin] ALSA: control 'Capture Volume'.
[rdpaudin] ALSA: control 'PCM Out Path & Mute'.
[rdpaudin] ALSA: control '3D Control - Switch'.
[rdpaudin] ALSA: control 'Mono Output Select'.
[rdpaudin] ALSA: control 'Mic Select'.
[rdpaudin] ALSA: control '3D Control - Center'.
[rdpaudin] ALSA: control '3D Control - Depth'.
[rdpaudin] ALSA: control 'External Amplifier'.
[rdpsnd] Card 'rev20'/'VIA 82C686A/B rev20 with AD1881A at 0xb800, irq 11'.
[rdpsnd] Mixer name: 'Analog Devices AD1881A'.
[rdpsnd] Components: 'AC97a:41445348'.
[rdpsnd] Controls: 31.
[rdpsnd] ALSA: control 'Master Playback Switch'.
[rdpsnd] ALSA: control 'Master Playback Volume'.
[rdpsnd] ALSA: control 'Master Mono Playback Switch'.
[rdpsnd] ALSA: control 'Master Mono Playback Volume'.
[rdpsnd] ALSA: control 'Beep Playback Switch'.
[rdpsnd] ALSA: control 'Beep Playback Volume'.
[rdpsnd] ALSA: control 'Phone Playback Switch'.
[rdpsnd] ALSA: control 'Phone Playback Volume'.
[rdpsnd] ALSA: control 'Mic Playback Switch'.
[rdpsnd] ALSA: control 'Mic Playback Volume'.
[rdpsnd] ALSA: control 'Mic Boost (+20dB)'.
[rdpsnd] ALSA: control 'Line Playback Switch'.
[rdpsnd] ALSA: control 'Line Playback Volume'.
[rdpsnd] ALSA: control 'CD Playback Switch'.
[rdpsnd] ALSA: control 'CD Playback Volume'.
[rdpsnd] ALSA: control 'Video Playback Switch'.
[rdpsnd] ALSA: control 'Video Playback Volume'.
[rdpsnd] ALSA: control 'Aux Playback Switch'.
[rdpsnd] ALSA: control 'Aux Playback Volume'.
[rdpsnd] ALSA: control 'PCM Playback Switch'.
[rdpsnd] ALSA: control 'PCM Playback Volume'.
[rdpsnd] ALSA: control 'Capture Source'.
[rdpsnd] ALSA: control 'Capture Switch'.
[rdpsnd] ALSA: control 'Capture Volume'.
[rdpsnd] ALSA: control 'PCM Out Path & Mute'.
[rdpsnd] ALSA: control '3D Control - Switch'.
[rdpsnd] ALSA: control 'Mono Output Select'.
[rdpsnd] ALSA: control 'Mic Select'.
[rdpsnd] ALSA: control '3D Control - Center'.
[rdpsnd] ALSA: control '3D Control - Depth'.
[rdpsnd] ALSA: control 'External Amplifier'.
[sndvol] Card 'rev20'/'VIA 82C686A/B rev20 with AD1881A at 0xb800, irq 11'.
[sndvol] Mixer name: 'Analog Devices AD1881A'.
[sndvol] Components: 'AC97a:41445348'.
[sndvol] Controls: 31.
[sndvol] ALSA: control 'Master Playback Switch'.
[sndvol] ALSA: control 'Master Playback Volume'.
[sndvol] ALSA: control 'Master Mono Playback Switch'.
[sndvol] ALSA: control 'Master Mono Playback Volume'.
[sndvol] ALSA: control 'Beep Playback Switch'.
[sndvol] ALSA: control 'Beep Playback Volume'.
[sndvol] ALSA: control 'Phone Playback Switch'.
[sndvol] ALSA: control 'Phone Playback Volume'.
[sndvol] ALSA: control 'Mic Playback Switch'.
[sndvol] ALSA: control 'Mic Playback Volume'.
[sndvol] ALSA: control 'Mic Boost (+20dB)'.
[sndvol] ALSA: control 'Line Playback Switch'.
[sndvol] ALSA: control 'Line Playback Volume'.
[sndvol] ALSA: control 'CD Playback Switch'.
[sndvol] ALSA: control 'CD Playback Volume'.
[sndvol] ALSA: control 'Video Playback Switch'.
[sndvol] ALSA: control 'Video Playback Volume'.
[sndvol] ALSA: control 'Aux Playback Switch'.
[sndvol] ALSA: control 'Aux Playback Volume'.
[sndvol] ALSA: control 'PCM Playback Switch'.
[sndvol] ALSA: control 'PCM Playback Volume'.
[sndvol] ALSA: control 'Capture Source'.
[sndvol] Capture Source [0] 'Mic'.
[sndvol] Capture Source [1] 'CD'.
[sndvol] Capture Source [2] 'Video'.
[sndvol] Capture Source [3] 'Aux'.
[sndvol] Capture Source [4] 'Line'.
[sndvol] Capture Source [5] 'Mix'.
[sndvol] Capture Source [6] 'Mix Mono'.
[sndvol] Capture Source [7] 'Phone'.
[sndvol] ALSA: control 'Capture Switch'.
[sndvol] ALSA: control 'Capture Volume'.
[sndvol] ALSA: control 'PCM Out Path & Mute'.
[sndvol] ALSA: control '3D Control - Switch'.
[sndvol] ALSA: control 'Mono Output Select'.
[sndvol] ALSA: control 'Mic Select'.
[sndvol] ALSA: control '3D Control - Center'.
[sndvol] ALSA: control '3D Control - Depth'.
[sndvol] ALSA: control 'External Amplifier'.
[pfac] Process pid 442 terminated, status 00000000.
[pfac] Got command line /usr/bin/linphonec -l /tmp/linphone.out --pipe.
[pfac] Ok, PID 443.
[gm] Load ISO 9660 and UDF CDROM filesystem drivers.
[gm] modprobe udf.
[SIP] /usr/bin/linphonec: error while loading shared libraries:
libosipparser2.so.7: cannot open shared object file: No such file or
directory
[SIP] close kotopipe (n = 0, errno 0).
[pfac] Process pid 443 terminated, status 00007f00.
[gm] modprobe isofs.
[gm] Load UTF8 charset.
[gm] modprobe nls_cp437.
[gm] modprobe nls_utf8.
[gm] Load VFAT filesystem driver.
[gm] modprobe fat.
[gm] modprobe vfat.
[gm] Load EXFAT filesystem driver.
[gm] TFTP: download and unpack file wtware.net/5.1.64/packages/fs from
192.168.0.1.
[gm] modprobe fuse.
[KERNEL] [ 13.263720] fuse init (API version 7.22)
[gm] modprobe exfat.
[KERNEL] [ 13.277308] exFAT: Version 1.2.9
[gm] Load IDE bus driver.
[gm] modprobe libata.
[KERNEL] [ 13.299626] SCSI subsystem initialized
[KERNEL] [ 13.317418] libata version 3.00 loaded.
[gm] modprobe pata_via.
[KERNEL] [ 13.331524] pata_via 0000:00:04.1: version 0.3.4
[KERNEL] [ 13.357581] scsi0 : pata_via
[KERNEL] [ 13.363663] scsi1 : pata_via
[KERNEL] [ 13.366883] ata1: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma
0xd800 irq 14
[KERNEL] [ 13.366902] ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma
0xd808 irq 15
[KERNEL] [ 13.520998] ata1.00: ATA-5: ST34313A, 3.23, max UDMA/66
[KERNEL] [ 13.521017] ata1.00: 8452080 sectors, multi 16: LBA
[KERNEL] [ 13.526916] ata1.00: configured for UDMA/66
[KERNEL] [ 13.527214] scsi 0:0:0:0: Direct-Access ATA ST34313A 3.23 PQ:
0 ANSI: 5
[gm] ATA module pata_via.ko loaded.
[gm] Load cdrom driver.
[gm] modprobe usb-storage.
[gm] modprobe sr_mod.
[KERNEL] [ 13.700833] usbcore: registered new interface driver usb-storage
[gm] Load usb storage driver.
[gm] modprobe scsi_mod.
[gm] modprobe usb-storage.
[gm] modprobe sd_mod.
[KERNEL] [ 13.747733] sd 0:0:0:0: [sda] 8452080 512-byte logical blocks:
(4.32 GB/4.02 GiB)
[KERNEL] [ 13.747897] sd 0:0:0:0: [sda] Write Protect is off
[KERNEL] [ 13.747909] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[KERNEL] [ 13.747981] sd 0:0:0:0: [sda] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
[KERNEL] [ 13.761441] sda: sda1
[KERNEL] [ 13.765255] sd 0:0:0:0: [sda] Attached SCSI disk
[gm] TFTP: download and unpack file wtware.net/5.1.64/packages/usbip
from 192.168.0.1.
[gm] Load USBIP stub driver.
[gm] modprobe usbip-host.
[KERNEL] [ 14.577315] usbip_core: module is from the staging directory,
the quality is unknown, you have been warned.
[KERNEL] [ 14.578126] usbip_core: USB/IP Core v1.0.0
[KERNEL] [ 14.578615] usbip_host: module is from the staging directory,
the quality is unknown, you have been warned.
[KERNEL] [ 14.584072] usbcore: registered new interface driver usbip-host
[KERNEL] [ 14.584091] usbip_host: USB/IP Host Driver v1.0.0
[gm] +--- Executing "/sbin/usbipd -D"
[gm] +- Errorlevel: 0, output:
File is empty.
[gm] +------------------------
[gm] /sys/bus/usb/devices/1-1:1.0/driver 09da:000a use driver usbhid.
[gm] USBIP: Device 09da:000a class 0x03 bus 1-1: not for usbip.
[SYSLOG] <29>May 30 11:46:27 modprobe: FATAL: Could not load
/lib/modules/3.13.11/modules.dep: No such file or directory

[SYSLOG] <14>May 30 11:46:27 usbipd: usbipd: info: starting usbipd
(usbip-utils 1.0.6)

[SYSLOG] <14>May 30 11:46:27 usbipd: usbipd: info: listening on 0.0.0.0:3240

[SYSLOG] <29>May 30 11:46:27 modprobe: FATAL: Could not load
/lib/modules/3.13.11/modules.dep: No such file or directory

[pfac] Got command line /sbin/resolver 09a5d598 dns [192.168.0.30].
[pfac] Ok, PID 536.
[gm] Nobody can control terminal by VNC.
[pfac] Process pid 536 terminated, status 00000000.
[pfac] Got command line /sbin/rdpclient 1.
[gm] SIP.h ( 35), SIP_int_send: -- ERROR -- INTERNAL ERROR. Please,
contact WTware tech support.
[pfac] Ok, PID 537.
[gm] SIP register failed.
[gm] 192.168.0.30 => 192.168.0.30.
[gm] Free ram before fork terminal client /sbin/rdpclient (session 1):
234076 Kb.
[rdpclient 537] RDP Terminal Client, WTware v.5.1.64, pipe 1, pid 537.
[rdpclient 537] Redirect sound.
[rdpclient 537] Make RDP session with 192.168.0.30:3389.
[rdpclient 537] No username.
[rdpclient 537] No password.
[rdpclient 537] Domain: "futu".
[rdpclient 537] No shell.
[rdpclient 537] No directory.
[rdpclient 537] Window: 960x768@16.
[rdpclient 537] PFlags 0x0000006F.
[rdpclient 537] Keyboard 00000419:00000000.
[rdpclient 537] My hostname "wt5client2".
[rdpclient 537] TCP: connecting to 192.168.0.30:3389.
[rdpclient 537] TCP: connection with 192.168.0.30:3389 established.
[rdpclient 537] Turn keepalive on.
[rdpclient 537] Free ram after buffers allocation: 230588 KB.
[rdpclient 537] RDP5 encryption (X.509).
[rdpclient 537] RC4 key 128 bit.
[rdpclient 537] Receive Disconnect Provider Ultimatum.
[pfac] Process pid 537 terminated, status 00000000.
[gm] TSClient gracefully end.
[rdpsnd] Link lost.
[rdpclient 537] Caught signal SIGTERM.
|
------------------------------------------------------------------------
Home </>   WTware <http://www.wtware.ru/doc.html> diskless client.
